MOTO GUZZI Stelvio 1200 MY11 2011 Service Station Manual Download Page 293 | Manualshive

Page: 293 / 385

background image

Standard rear shock absorber setting is adjusted

to suit most high and low speed riding conditions,

to transport the rider plus luggage.

However, this set can be modified for specific

needs according to vehicle use.

BEFORE MAKING ANY ADJUSTMENTS, WAIT FOR THE
ENGINE AND SILENCER TO COOL COMPLETELY.

ADJUSTMENTS

Regular adjustment (standard):

- rider only.

Half load adjustment:

- (for example, rider with passenger or with luggage).

Maximum load adjustment:

- (e.g. rider, passenger and luggage).

CAUTION

SET SPRING PRELOADING AND SHOCK ABSORBER REBOUND DAMPING ACCORDING TO
THE VEHICLE USE CONDITIONS. HYDRAULIC REBOUND DAMPING MUST ALWAYS BE IN-
CREASED TOGETHER WITH SPRING PRELOAD TO PREVENT UNDESIRABLE BOUNCING. IF
NECESSARY, CONTACT AN Official Moto Guzzi Dealer. TRY RIDING THE VEHICLE ON THE
STREET UNTIL THE OPTIMUM ADJUSTMENT IS OBTAINED.

SHOCK ABSORBER SETTING TABLE

Regular load adjustments are the standard settings by manufacturer

REAR SHOCK ABSORBER ADJUSTMENT

Specification

Desc./Quantity

Preload - regular load conditions

15 clicks starting from knob (2) fully loosened

Preload - half-load conditions

28 clicks starting from knob (2) fully loosened

Preload - maximum load conditions

33 clicks starting from knob (2) fully loosened

Rebound - regular load conditions

24 clicks starting from screw (1) fully tightened

Rebound - half -load conditions

20 clicks starting from screw (1) fully tightened

Rebound - maximum load conditions

18 clicks starting from screw (1) fully tightened

(1) THE SETTING SHOWN IN THE TABLE MAY NEED TO BE MODIFIED ACCORDING TO THE
TYRE AND ROAD TYPE.

NOTE

(2) IF FITTED.

Stelvio 1200 NTX MY11

Suspensions

SUSP - 293

«
...
291
292
293
294
295
...
»

Summary of Contents for Stelvio 1200 MY11 2011


































































































































































































































































































































































































Reviews:

No comments

Related manuals for Stelvio 1200 MY11 2011

Brand: ICON Pages: 8

Brand: Tao Motor Pages: 3

ALK.00.733.15000/B

Brand: SW-Motech Pages: 14

Brand: Dakota Digital Pages: 6

Brand: Takegawa Pages: 2

Brand: OKBABY Pages: 35

Brand: Yamaha Pages: 98

Star XVS13CB(C)

Brand: Yamaha Pages: 100

Brand: Yamaha Pages: 96

Brand: Yamaha Pages: 145

ROADLINER XV19SW

Brand: Yamaha Pages: 444

Brand: Yamaha Pages: 494

Brand: Yamaha Pages: 94

Brand: Yamaha Pages: 120

Brand: hepco & becker Pages: 3

Brand: Arai Helmet Pages: 28

Brand: Race Dynamics Pages: 25

Brand: RIEJU Pages: 280

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands