MOTO GUZZI Stelvio 1200 MY11 2011 Service Station Manual Download Page 105

Page: 105 / 385

OK, check that the tyre pressure is the correct one. If it is not OK, restore it; if it is OK, replace the speed

sensor.

REAR

FUNCTION:

It is used by the ABS module, and

then by the ECU and the instrument panel.

OPERATION / OPERATING PRINCIPLE:

Differ-

ential Hall effect sensor.

ELECTRICAL CIRCUIT DIAGRAM

- Level in wir-

ing diagram: ABS.

REMOVAL

LOCATION ON THE VEHICLE:

Under the bevel

gear set box, right side.

CONNECTOR LOCATION (if available):

Under

the saddle, right side.

PIN-OUT:

•

PIN1 - Ground

•

PIN2 - Signal

NAVIGATOR: PARAMETERS

Speed sensor

Vehicle speed: km/h

REAR SPEED SENSOR OPEN CIRCUIT OR SHORT CIRCUIT NAVIGATOR ERROR

Description of the defect:

the control unit detects abnormal voltage in the rear speed sensor signal.

Checks:

check battery voltage on the cable between pin 2 of the rear speed sensor connector and pin

11 of the ABS module connector. If there is not enough voltage, check cable continuity from the ABS

module to the speed sensor connector and make sure that the cable is ground insulated.

Solution:

restore wiring. It is normal that when the speed sensor connector is disconnected, no voltage

is detected.

If functioning is correct, proceed to the next check

Checks:

check the speed sensor signal (0.5 or 1 V) on the cable between pin 1 of the rear speed sensor

connector and pin 12 of the ABS module connector. If there is not enough voltage, check cable continuity

from the ABS module to the speed sensor connector and make sure that the cable is grounded insulated.

Solution:

if the cable is interrupted or grounded, restore wiring.

If the cable harness is not damaged, it means that the speed sensor is defective or the circuit between

sensor and connector is interrupted: replace the speed sensor.

FRONT / REAR SPEED SENSOR COHERENCE NAVIGATOR ERROR

Stelvio 1200 NTX MY11

Electrical system

ELE SYS - 105

Summary of Contents for Stelvio 1200 MY11 2011


































































































































































































































































































































































































Search results

Summary of Contents for Stelvio 1200 MY11 2011

Reviews:

MOTO GUZZI Stelvio 1200 MY11 2011, Service Station Manual, Page: 105 / 385

Search results

Summary of Contents for Stelvio 1200 MY11 2011

Reviews: