manualshive.com logo in svg

MOTO GUZZI Stelvio 1200 MY11 2011, Service Station Manual

The MOTO GUZZI Stelvio 1200 MY11 2011 Service Station Manual is a comprehensive guide for motorcycle enthusiasts. This invaluable manual covers everything from maintenance procedures to troubleshooting tips, ensuring that riders can keep their Stelvio 1200 running smoothly. Download this manual for free at manualshive.com and unleash the full potential of your bike.

Share
Download
background image

km x 1.000 (mi x 1.000)

1.5

(0.9)

10

(6.2)

20

(12.4)

30

(18.6)

40

(28.4)

50

(31.1)

60

(37.3)

70

(43.5)

80

(49.7)

Footrests joint (5)

I

I

I

I

I

I

I

I

Suspension and setting

I

I

I

I

I

Engine oil pressure warning light (4)
Empty oil drain pipe from the filter housing

C

C

C

C

C

C

C

C

Fuel lines (3)

I

I

I

I

I

I

I

I

Brake lines (3)

I

I

I

I

I

I

I

I

Clutch wear

I

I

I

I

I

I

I

I

Brake pad wear (1)

I

I

I

I

I

I

I

I

I

Labour time (minutes)

150

230

210

230

210

240

210

230

210

NOTE

AT EACH SCHEDULED MAINTENANCE MUST BE VERIFIED WITH THE DIAGNOSTIC TOOL IF
THERE ARE ERRORS AND THE IF THE PARAMETERS ARE CORRECT.

Transmission fluid

Check

• Keep the vehicle upright with both wheels on the

ground.

• Unscrew and remove the cap/dipstick (1).

• The level is correct if the oil is close to the hole

of the cap/dipstick (1).

• If the oil is lower than specified, top-up until it

reaches the cap/dipstick hole (1).

CAUTION

DO NOT ADD ADDITIVES OR OTHER SUBSTANCES TO
THE FLUID. WHEN USING A FUNNEL OR ANY OTHER EL-
EMENT, MAKE SURE IT IS PERFECTLY CLEAN.

Replacement

CAUTION

THE UNIT MUST BE HOT WHEN THE OIL IS CHANGED AS UNDER SUCH CONDITIONS OIL IS
FLUID AND THEREFORE EASY TO DRAIN.

NOTE

RIDE SOME km (miles) TO WARM UP ENGINE OIL

•

Place a container with + 400 cm³ (25 cu in) capacity under the drainage plug (3).

•

Unscrew and remove the drainage plug (3).

•

Unscrew and remove the breather cap (2).

•

Drain the oil into the container; allow several minutes for oil to drain out completely.

•

Check and if necessary, replace the sealing washer of drainage plug (3).

•

Remove any metal scrap attached to the drainage plug (3) magnet.

•

Screw and tighten the drainage plug (3).

•

Pour new oil through the fill opening (1) until it reaches the cap/dipstick hole (1).

Stelvio 1200 NTX MY11

Maintenance

MAIN - 63

Summary of Contents for Stelvio 1200 MY11 2011


































































































































































































































































































































































































Reviews:

No comments

Related manuals for Stelvio 1200 MY11 2011

Bajaj Pulsar 150 DTS-i User Manual preview
Pulsar 150 DTS-i
Brand: Bajaj Pages: 33
Baja motorsports DR125 Owner'S Manual preview
DR125
Brand: Baja motorsports Pages: 37
Bajaj Dominar 250 BS VI Owner'S Manual preview
Dominar 250 BS VI
Brand: Bajaj Pages: 52
Baja motorsports DB30 Mini Bike Service Bulletin preview
DB30 Mini Bike
Brand: Baja motorsports Pages: 4
Bajaj Auto Dominar 400 Owner'S Manual preview
Dominar 400
Brand: Bajaj Auto Pages: 40
yasuni TUB653 Assembly Instructions Manual preview
TUB653
Brand: yasuni Pages: 8
Mash Two Fifty 250 cc User Manual preview
Two Fifty 250 cc
Brand: Mash Pages: 62
Nolan N60-5 Safety And Instructions For Use preview
N60-5
Brand: Nolan Pages: 80
Honda XL125LK Owner'S Manual preview
XL125LK
Brand: Honda Pages: 243
GAS GAS EX 250 2023 Owner'S Manual preview
EX 250 2023
Brand: GAS GAS Pages: 144
Ciro CYBERCHARGER 50002 Manual preview
CYBERCHARGER 50002
Brand: Ciro Pages: 3
Thermo Soles TS-03 Instructions Manual preview
TS-03
Brand: Thermo Soles Pages: 13
Power Fist 8808560 Instructions preview
8808560
Brand: Power Fist Pages: 2
Power Fist 8674285 User Manual preview
8674285
Brand: Power Fist Pages: 16
O'Neal TIRADE User Manual preview
TIRADE
Brand: O'Neal Pages: 12
RIEJU MRX-SMX 50 Chassis Workshop Manual preview
MRX-SMX 50
Brand: RIEJU Pages: 52
Yamaha V-Star XVS250S Owner'S Manual preview
V-Star XVS250S
Brand: Yamaha Pages: 82
Yamaha V Star XVS250S Owner'S Manual preview
V Star XVS250S
Brand: Yamaha Pages: 82

Brands by name

Popular brands

Load more brands