MOTO GUZZI Stelvio 1200 MY11 2011 Service Station Manual Download Page 126

Page: 126 / 385

Air temperature sensor - instrument panel

Function

It tells the ambient air temperature to the instru-

ment panel.

Operation / Operating principle

NTC type sensor (resistance sensor, inversely

variable with temperature).

Level in electrical circuit diagram:

Temperature

sensors

Location:

•

sensor: under the instrument panel

•

Connector: sotto al cruscotto, lato sin-

istro

Electrical characteristics:

•

Resistance at 0 °C (32 °F): 32.5 kOhm

+/- 5%

•

Resistance at 25 °C (77 °F): 10.0

kOhm +/- 5%

Pin-out:

1. Voltage 5V

2. Ground connection

Instrument panel

Air temperature sensor failure

DSB 06

Error cause

•

An oil sensor failure is signalled when it is detected that the sensor circuit is open or shorted

to positive

Troubleshooting

•

Check the sensor connector and the instrument panel connector (PINS 10 and 18): If they

are not OK, restore. If OK, check continuity of the pink cable between the sensor connector

and the instrument panel connector PIN 10: if it is not OK, restore the cable harness; if OK,

check the correct sensor resistance: if it is not OK, replace the sensor; if it is OK, check

continuity of the brown cable between the sensor connector and PIN 18 of the instrument

panel connector: If not OK, restore the cable harness; if OK, with key set to ON, check if

there is voltage at the sensor connector PIN 1: if there is no voltage, replace the instrument

panel; if there is approximately 12V, restore the cable harness (there is a short circuit in the

battery). If there is 5V voltage, connect a 10 kOhm resistance to PIN 1 of the sensor con-

nector and to the vehicle ground connection: if, with key set to ON, the voltage measured

Electrical system

Stelvio 1200 NTX MY11

ELE SYS - 126

Summary of Contents for Stelvio 1200 MY11 2011


































































































































































































































































































































































































Search results

Summary of Contents for Stelvio 1200 MY11 2011

Reviews:

Related manuals for Stelvio 1200 MY11 2011

Brands by name

Popular brands

MOTO GUZZI Stelvio 1200 MY11 2011, Service Station Manual

Search results

Summary of Contents for Stelvio 1200 MY11 2011

Reviews:

Related manuals for Stelvio 1200 MY11 2011

Brands by name

Popular brands