manualshive.com logo in svg

MOTO GUZZI Stelvio 1200 MY11 2011, Service Station Manual

The MOTO GUZZI Stelvio 1200 MY11 2011 Service Station Manual is a comprehensive guide for motorcycle enthusiasts. This invaluable manual covers everything from maintenance procedures to troubleshooting tips, ensuring that riders can keep their Stelvio 1200 running smoothly. Download this manual for free at manualshive.com and unleash the full potential of your bike.

Share
Download
background image

- Through the diagnosis tool, check that the last mapping version is present in the control unit/s and, if

required, program the control unit/s again: consult the technical service website to know about available

upgrades and details regarding the operation.

CAUTION

TO ENSURE MAXIMUM PERFORMANCE, THE BATTERY MUST BE CHARGED BEFORE USE.
INADEQUATE CHARGING OF THE BATTERY WITH A LOW LEVEL OF ELECTROLYTE BEFORE
IT IS FIRST USED SHORTENS BATTERY LIFE.

CAUTION

WHEN INSTALLING THE BATTERY, ATTACH THE POSITIVE LEAD FIRST AND THEN THE NEG-
ATIVE ONE, AND PERFORM THE REVERSE OPERATION DURING REMOVAL.

WARNING

THE BATTERY ELECTROLYTE IS POISONOUS AS IT MAY CAUSE SERIOUS BURNS. IT CON-
TAINS SULPHURIC ACID. AVOID CONTACT WITH YOUR EYES, SKIN AND CLOTHING.
IF IT ACCIDENTALLY COMES INTO CONTACT WITH YOUR EYES OR SKIN, WASH WITH ABUN-
DANT WATER FOR APPROX. 15 MIN. AND SEEK IMMEDIATE MEDICAL ATTENTION.
IF ACCIDENTALLY SWALLOWED, IMMEDIATELY DRINK LARGE QUANTITIES OF WATER OR
VEGETABLE OIL. SEEK IMMEDIATE MEDICAL ATTENTION.
BATTERIES PRODUCE EXPLOSIVE GASES; KEEP CLEAR OF NAKED FLAMES, SPARKS OR
CIGARETTES. VENTILATE THE AREA WHEN RECHARGING INDOORS. ALWAYS WEAR EYE
PROTECTION WHEN WORKING IN THE PROXIMITY OF BATTERIES.
KEEP OUT OF THE REACH OF CHILDREN

CAUTION

NEVER USE FUSES WITH A CAPACITY HIGHER THAN THE RECOMMENDED CAPACITY. USING
A FUSE OF UNSUITABLE RATING MAY SERIOUSLY DAMAGE THE VEHICLE OR EVEN CAUSE
A FIRE.

Levels check

- Hydraulic braking system fluid level

- Clutch system fluid level (if present)

- Gearbox oil level (if present)

- Transmission oil level (if present)

- Engine coolant level (if present)

- Engine oil level

- Mixer oil level (if present)

Road test

- Cold start

- Instrument panel operation

Pre-delivery

Stelvio 1200 NTX MY11

PRE DE - 380

Summary of Contents for Stelvio 1200 MY11 2011


































































































































































































































































































































































































Reviews:

No comments

Related manuals for Stelvio 1200 MY11 2011

N-Com SPCOM00000091 Quick Start Manual preview
SPCOM00000091
Brand: N-Com Pages: 6
R&G LP0107BK Fitting Instructions Manual preview
LP0107BK
Brand: R&G Pages: 14
SSR Motorsports SR250S Owner'S Manual preview
SR250S
Brand: SSR Motorsports Pages: 39
Wedze IM 16 S Manual preview
IM 16 S
Brand: Wedze Pages: 63
Honda ST1300 2004 Setup Instructions preview
ST1300 2004
Brand: Honda Pages: 26
HERO ACHIEVER 150 Manual preview
ACHIEVER 150
Brand: HERO Pages: 68
Rekluse TorqDrive Clutch Pack Installation & User Manual preview
TorqDrive Clutch Pack
Brand: Rekluse Pages: 18
Two Brothers Racing 005-3860405-S1 Installation Instructions preview
005-3860405-S1
Brand: Two Brothers Racing Pages: 2
BMW F 650 GS Manual preview
F 650 GS
Brand: BMW Pages: 88
hepco & becker 504980 00 05 Quick Manual preview
504980 00 05
Brand: hepco & becker Pages: 2
Yamaha T115FL-2 Owner'S Manual preview
T115FL-2
Brand: Yamaha Pages: 80
Yamaha RT100 Owner'S Manual preview
RT100
Brand: Yamaha Pages: 63
Yamaha SR125 Owner'S Manual preview
SR125
Brand: Yamaha Pages: 78
Yamaha Star XVS95CE Owner'S Manual preview
Star XVS95CE
Brand: Yamaha Pages: 94
Yamaha Star XV1900AE 2013 Owner'S Manual preview
Star XV1900AE 2013
Brand: Yamaha Pages: 92
Yamaha Sniper T135 SE Owner'S Manual preview
Sniper T135 SE
Brand: Yamaha Pages: 84
Yamaha Star XV19MY Owner'S Manual preview
Star XV19MY
Brand: Yamaha Pages: 94
Yamaha SCORPIO 54D Owner'S Manual preview
SCORPIO 54D
Brand: Yamaha Pages: 86

Brands by name

Popular brands

Load more brands