MOTO GUZZI Stelvio 1200 MY11 2011 Service Station Manual Download Page 333 | Manualshive

Page: 333 / 385

background image

light (5) on the instrument panel (4)

turns off.

CAUTION

IF THE ABS SWITCH IS PRESSED FOR MORE THAN TEN
SECONDS, THE SYSTEM DETECTS A FAILURE. TO ACTI-
VATE THE ABS SYSTEM AGAIN TURN THE IGNITION
SWITCH TO "OFF" AND THEN TO "ON".

IN CASE OF FAILURE OR WITH ABS DISCONNECTED,
THE VEHICLE OPERATES AS IF IT DID NOT HAVE THIS
SYSTEM.

20 A fuse (ABS Main fuse) (6)

Protects: ABS Control unit.

Guide to diagnosis

PREMISE

Each time the key is ON, if, at least one current or

stored* error is detected, the ABS warning light

turns on permanently.

The ABS system is deactivated!

The system operates perfectly just as any other

braking system without ABS

* The diagnosis requires exceeding the 5 km/h

(3.1 mph).

Each time the key is ON, if at least one current or stored* error of the ABS system is not detected:

•

the abs warning light flashes.

When the 5 km/h (3.1 mph) are exceeded:

- if errors are not detected: the ABS warning light turns off

- if at least one malfunction is detected: the ABS warning light turns on permanently.

The ABS system is disabled!

The system operates perfectly just as any other braking system without ABS.

The detection of malfunctions may require more or less time according to the type of failure.

Error detection logic foresees that for the errors to be diagnosed one or more conditions must persist

within a given time.

Stelvio 1200 NTX MY11

Braking system

BRAK SYS - 333

«
...
331
332
333
334
335
...
»

Summary of Contents for Stelvio 1200 MY11 2011


































































































































































































































































































































































































Reviews:

No comments

Related manuals for Stelvio 1200 MY11 2011

Brand: Yamaha Pages: 568

Brand: FDC Pages: 6

Operation and Instruction Manua

Brand: Takegawa Pages: 9

80 MasterGuard (L+K)

Brand: SCHUBERTH Pages: 44

V-Star XVS1100AWT

Brand: Yamaha Pages: 93

Venture XVZ13TFV

Brand: Yamaha Pages: 123

Venture XVZ13TFS

Brand: Yamaha Pages: 121

Venture XVZ13TFT

Brand: Yamaha Pages: 123

Venture XVZ13TFW

Brand: Yamaha Pages: 124

Brand: Yamaha Pages: 98

Brand: BMW Pages: 88

Brand: DYNATEK Pages: 4

Brand: Kask Pages: 24

Brand: Ossa Pages: 72

Brand: DAINESE Pages: 144

VarioProtect XXL-W TC AIR TH3

Brand: schweisskraft Pages: 28

Elefant 650 USA

Brand: Cagiva Pages: 136

Brand: R&G Pages: 19

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands