manualshive.com logo in svg

MOTO GUZZI Stelvio 1200 MY11 2011, Service Station Manual

The MOTO GUZZI Stelvio 1200 MY11 2011 Service Station Manual is a comprehensive guide for motorcycle enthusiasts. This invaluable manual covers everything from maintenance procedures to troubleshooting tips, ensuring that riders can keep their Stelvio 1200 running smoothly. Download this manual for free at manualshive.com and unleash the full potential of your bike.

Share
Download
background image

•

When the connector is fully inserted,

the distance between the connector

and the ABS control unit must be 7.5

mm (0.29 in).

•

If the initial position of the connector

and the driving lever is not that shown

in fig. 1, the connector will not be prop-

erly coupled and the distance meas-

ured will be greater (12 mm approx.

(0.47 in)). In this case repeat the oper-

ation as described in the two previous

points.

IT IS ADVISABLE TO CREATE A TEMPLATE

TO CHECK THE CORRECT CONNECTOR IN-

SERTION.

•

Fit the protection casing.

Component maintenance

The vehicle is fitted with a two-channel ABS sys-

tem, i.e. it works on both the front and the rear

wheel.

Check periodically and each time the wheels are

refitted, the tone wheel (2) or the sensor (1) re-

placed, that the wheel distance is constant at each

360°. Use a thickness gauge to check the distance

between sensor (1) and tone wheel (2) at three

points at a 120° span. The values should be be-

tween:

Braking system

Stelvio 1200 NTX MY11

BRAK SYS - 340

Summary of Contents for Stelvio 1200 MY11 2011


































































































































































































































































































































































































Reviews:

No comments

Related manuals for Stelvio 1200 MY11 2011

Cannondale E440 Owner'S Manual preview
E440
Brand: Cannondale Pages: 102
KAYO MOTOR K4 Service Manual preview
K4
Brand: KAYO MOTOR Pages: 74
KAYO MOTO K4 Assembly Manual preview
K4
Brand: KAYO MOTO Pages: 5
Yamaha Tmax XP500Z Owner'S Manual preview
Tmax XP500Z
Brand: Yamaha Pages: 102
STEEL HORSE AUDIO ST400 Cruiser Edition Installation Instructions Manual preview
ST400 Cruiser Edition
Brand: STEEL HORSE AUDIO Pages: 6
KTM 450 SX-F 2019 Owner'S Manual preview
450 SX-F 2019
Brand: KTM Pages: 163
AGV CORSA R Manual preview
CORSA R
Brand: AGV Pages: 45
Honda NSC110 2020 Manual preview
NSC110 2020
Brand: Honda Pages: 137
Dakota Digital MLX-3000 Manual preview
MLX-3000
Brand: Dakota Digital Pages: 11
Yamaha VMX12 93 Supplementary Service Manual preview
VMX12 93
Brand: Yamaha Pages: 24
Yamaha WR250F(R) Assembly Manual preview
WR250F(R)
Brand: Yamaha Pages: 34
Yamaha VMX17YB 2009 Assembly Manual preview
VMX17YB 2009
Brand: Yamaha Pages: 44
Yamaha WR 155 Owner'S Manual preview
WR 155
Brand: Yamaha Pages: 92
Yamaha WARRIOR XV17PCT Owner'S Manual preview
WARRIOR XV17PCT
Brand: Yamaha Pages: 97
Yamaha WARRIOR XV17PCC Owner'S Manual preview
WARRIOR XV17PCC
Brand: Yamaha Pages: 97
Yamaha Virago XV535L Owner'S Manual preview
Virago XV535L
Brand: Yamaha Pages: 96
Yamaha Virago XV535 Owner'S Manual preview
Virago XV535
Brand: Yamaha Pages: 96
Yamaha VIRAGO XV250T Owner'S Manual preview
VIRAGO XV250T
Brand: Yamaha Pages: 95

Brands by name

Popular brands

Load more brands