manualshive.com logo in svg

MOTO GUZZI Stelvio 1200 MY11 2011, Service Station Manual, Page: 379 / 385

Share
Download
MOTO GUZZI Stelvio 1200 MY11 2011 Service Station Manual Download Page 379

Carry out the listed checks before delivering the motorcycle.

WARNING

HANDLE FUEL WITH CARE.

Aesthetic inspection

- Paintwork

- Fitting of Plastic Parts

- Scratches

- Dirt

Tightening torques inspection

- Safety fasteners:

front and rear suspension unit

front and rear brake calliper retainer unit

front and rear wheel unit

engine - chassis retainers

steering assembly

- Plastic parts fixing screws

Electrical system

- Main switch

- Headlamps: high beam lights, low beam lights, tail lights (front and rear) and their warning lights

- Headlight adjustment according to regulations in force

- Front and rear stop light switches and their bulbs

- Turn indicators and their warning lights

- Instrument panel lights

- Instrument panel: fuel and temperature indicator (if present)

- Instrument panel warning lights

- Horn

- Electric starter

- Engine stop via emergency stop switch and side stand

- Helmet compartment electrical opening switch (if present)

Stelvio 1200 NTX MY11

Pre-delivery

PRE DE - 379

Summary of Contents for Stelvio 1200 MY11 2011


































































































































































































































































































































































































Reviews:

No comments