manualshive.com logo in svg

MOTO GUZZI Stelvio 1200 MY11 2011, Service Station Manual

The MOTO GUZZI Stelvio 1200 MY11 2011 Service Station Manual is a comprehensive guide for motorcycle enthusiasts. This invaluable manual covers everything from maintenance procedures to troubleshooting tips, ensuring that riders can keep their Stelvio 1200 running smoothly. Download this manual for free at manualshive.com and unleash the full potential of your bike.

Share
Download
background image

•

The measurement must be taken using

a special thickness gauge.

CAUTION

IF CLEARANCE IS LARGER THAN RECOMMENDED, THE
TAPPETS WILL BE NOISY. OTHERWISE, THE VALVES DO
NOT CLOSE CORRECTLY, WHICH CAN LEAD TO PROB-
LEMS SUCH AS:

•

PRESSURE DROP;

•

ENGINE OVERHEAT;

•

VALVE BURN OUT, ETC.

Braking system

Level check

Brake fluid check

•

Rest the vehicle on its stand.

•

For the front brake, turn the handlebar fully to the right.

•

For the rear brake, keep the vehicle upright so that the fluid in the reservoir is at the same

level with the plug.

•

Make sure that the fluid level in the reservoir is above the "MIN" reference mark:

MIN

 = minimum level

MAX

 = maximum level

If the fluid does not reach at least the "

MIN

" reference mark:

•

Check brake pads and disc for wear.

•

If the pads and/or the disc do not need replacing, top-up the fluid.

Top-up

Front brake:

•

Unscrew the two screws (1) of the

brake fluid reservoir (2) using a Phillips

screwdriver.

•

Lift and remove the cover (3) and

screws (1) as well.

•

Remove the gasket (4).

Rear brake:

•

Unscrew and remove the cap (5).

•

Remove the gasket (6).

Maintenance

Stelvio 1200 NTX MY11

MAIN - 70

Summary of Contents for Stelvio 1200 MY11 2011


































































































































































































































































































































































































Reviews:

No comments

Related manuals for Stelvio 1200 MY11 2011

Kabuto FLAIR Instruction Manual preview
FLAIR
Brand: Kabuto Pages: 25
KYMCO Quannon 125 Driver Manual preview
Quannon 125
Brand: KYMCO Pages: 58
Dakota Digital MCL-36K-SPD Installation Manual preview
MCL-36K-SPD
Brand: Dakota Digital Pages: 6
Zero DSR 2018 Owner'S Manual preview
DSR 2018
Brand: Zero Pages: 162
Free Spirits 308927 Instructions Manual preview
308927
Brand: Free Spirits Pages: 28
Yamaha XS650SE Shop Manual preview
XS650SE
Brand: Yamaha Pages: 215
Yamaha XS1100SH Service Manual preview
XS1100SH
Brand: Yamaha Pages: 319
Yamaha TMAX 2020 Service Manual preview
TMAX 2020
Brand: Yamaha Pages: 688
Yamaha XMAX YP250R 2013 Owner'S Manual preview
XMAX YP250R 2013
Brand: Yamaha Pages: 94
KTM 60112092010 Information preview
60112092010
Brand: KTM Pages: 7
hepco & becker 5039505 00 01 Quick Start Manual preview
5039505 00 01
Brand: hepco & becker Pages: 2
SpeedAngle GMOS JI100S User Manual preview
GMOS JI100S
Brand: SpeedAngle Pages: 37
CZ Sport 1 180 - 487.3 Workshop Manual preview
Sport 1 180 - 487.3
Brand: CZ Pages: 42
Cagiva Roadster 521 Workshop Manual preview
Roadster 521
Brand: Cagiva Pages: 230
RIEJU MARATHON 125 AC Owner'S Manual preview
MARATHON 125 AC
Brand: RIEJU Pages: 40
hepco & becker 661998 01 01 Manual preview
661998 01 01
Brand: hepco & becker Pages: 4
hepco & becker 6622526 01 01 Manual preview
6622526 01 01
Brand: hepco & becker Pages: 4
KTM 27112912044 Fitting Instructions Manual preview
27112912044
Brand: KTM Pages: 53

Brands by name

Popular brands

Load more brands