manualshive.com logo in svg

MOTO GUZZI Stelvio 1200 MY11 2011, Service Station Manual, Page: 338 / 385

Share
Download
MOTO GUZZI Stelvio 1200 MY11 2011 Service Station Manual Download Page 338

SETTINGS screen page

This screen page is used to adjust some control

unit parameters.

ADJUSTMENTS

Characteristic

Value/example

Unit of

measure

ment

Notes

Coding (1)

Used for re-coding the control unit or coding a new

one.

Coding (2)

Vehicle identification is done according to the con-

nection of PINS 2 and 15 of the ABS control unit

connector and is stored in the control unit memory.

Coding (3)

The identification can be read in the INFO ECU

screen page in the line: Vehicle code.

NOTE: the "X" in the table identifies the connector pin is grounded.

ABS 

CONNECTOR

 

IS

 

GROUNDED

Vehicle

PIN 2

PIN 15

Stelvio 1200 4V ABS

X

Norge 1200 4V ABS

X

Abs screen pages

Modulator

•

Remove the fuel tank.

•

Cut the cable harness clamp.

Braking system

Stelvio 1200 NTX MY11

BRAK SYS - 338

Summary of Contents for Stelvio 1200 MY11 2011


































































































































































































































































































































































































Reviews:

No comments