manualshive.com logo in svg

MOTO GUZZI Stelvio 1200 MY11 2011, Service Station Manual

The MOTO GUZZI Stelvio 1200 MY11 2011 Service Station Manual is a comprehensive guide for motorcycle enthusiasts. This invaluable manual covers everything from maintenance procedures to troubleshooting tips, ensuring that riders can keep their Stelvio 1200 running smoothly. Download this manual for free at manualshive.com and unleash the full potential of your bike.

Share
Download
background image

CAUTION

DO NOT ADD ADDITIVES OR OTHER SUBSTANCES TO THE FLUID. WHEN USING A FUNNEL
OR ANY OTHER ELEMENT, MAKE SURE IT IS PERFECTLY CLEAN.

•

Screw and tighten the caps (1 - 2).

Engine oil

Check

CAUTION

ENGINE MUST BE WARM TO CHECK ENGINE OIL LEVEL.

NOTE

DO NOT LET THE ENGINE IDLE WITH THE VEHICLE AT STANDSTILL TO WARM UP THE ENGINE
OIL AND REACH THE OPERATING TEMPERATURE OF ENGINE OIL. OIL IS BEST CHECKED
AFTER RUNNING FOR ABOUT 15 KM (10 miles).

•

Shut off the engine.

•

Keep the vehicle upright with both wheels on the ground.

•

Pull the filler plug / oil level dipstick (1)

straight out.

•

Wipe the oil level dipstick (1) clean and

reinsert it.

•

Pull it out again and check the oil level.

•

The oil level is correct when it is close

to the "MAX" mark. Otherwise, top-up

with engine oil.

CAUTION

DO NOT ADD ADDITIVES OR OTHER SUBSTANCES TO THE FLUID. WHEN USING A FUNNEL
OR ANY OTHER ELEMENT, MAKE SURE IT IS PERFECTLY CLEAN.

Replacement

NOTE

HOT OIL IS MORE FLUID AND WILL DRAIN OUT MORE EASILY AND COMPLETELY.

It is necessary to remove the metal oil sump guard in order to change the engine oil and replace the oil

filter:

Maintenance

Stelvio 1200 NTX MY11

MAIN - 64

Summary of Contents for Stelvio 1200 MY11 2011


































































































































































































































































































































































































Reviews:

No comments

Related manuals for Stelvio 1200 MY11 2011

R&G LP0274BK Fitting Instructions Manual preview
LP0274BK
Brand: R&G Pages: 24
KTM 200 EXC 2016 Setup Instructions preview
200 EXC 2016
Brand: KTM Pages: 25
rizoma BS232 User Manual preview
BS232
Brand: rizoma Pages: 16
TVS WEGO 110 Fi Owner'S Manual preview
WEGO 110 Fi
Brand: TVS Pages: 60
Baja motorsports Dirt Runner 90 Owner'S Manual preview
Dirt Runner 90
Brand: Baja motorsports Pages: 66
DYNATEK DDK1-9 Installation Manual preview
DDK1-9
Brand: DYNATEK Pages: 12
ChatterBox X1slim User Manual preview
X1slim
Brand: ChatterBox Pages: 10
Rovo Kids Ride-On Motorcycle User Manual preview
Ride-On Motorcycle
Brand: Rovo Kids Pages: 17
Cagiva 1994 MITO ev Workshop Manual preview
1994 MITO ev
Brand: Cagiva Pages: 124
Deco Hannah Manual preview
Hannah
Brand: Deco Pages: 40
APRILIA LEONARDO 125 Manual preview
LEONARDO 125
Brand: APRILIA Pages: 264
Abus 440A Instructions preview
440A
Brand: Abus Pages: 4
KTM 78111994000 Information preview
78111994000
Brand: KTM Pages: 7
Gazzini 10039781 Instructions For Use Manual preview
10039781
Brand: Gazzini Pages: 24
A.J.S. 16 Instruction Book preview
16
Brand: A.J.S. Pages: 104
SHOEI HORNET ADV Instructions For Use Manual preview
HORNET ADV
Brand: SHOEI Pages: 42
HealTech Electronics QuickShifter User Manual preview
QuickShifter
Brand: HealTech Electronics Pages: 4
HealTech Electronics SH-HY1 Install Manual preview
SH-HY1
Brand: HealTech Electronics Pages: 2

Brands by name

Popular brands

Load more brands