Minebea Intec PR 5230 Instrument Manual Download

Page: 84 / 303

NOTICE

The

rotary switch settings will not be used.

Ensure that the three rotary switches for node address 1

99 are set to posi-

tion "0."

Settings are defined via

- [Fieldbus parameter][Profibus-DP].

4.6.5.2

Status indicator

Requirements:

The items are defined via

- [Display items]- [Fieldbus LEDs]; see Chapter

7.15.7

PR 1721/41 is selected via

- [HW-Slots]- [Slot 2].

Display:

Constant

---

No function

Constant

grn

Module is online, da-
ta transmission is
possible.

Flashing 1 Hz

red

Input/output length
configuration error.

Constant

red

Fieldbus is offline,
data transmission is
not possible.

Flashing 2 Hz

red

User parameter error

Flashing 4 Hz

red

Error in ASIC

Legend

---

off

red

grn

green

4.6.5.3

Bus termination

The end nodes in a ProfiBus-DP network must be fitted with termination resistors, to
prevent reflections in the bus cable.

Bus termination switch

can only be accessed when the device

has been opened.

4 Device installation

Transmitter in field housing PR 5230

EN-81

Minebea Intec

Summary of Contents for PR 5230
















































































































































































































































































































Search results

Summary of Contents for PR 5230

Reviews:

Related manuals for PR 5230

Brands by name

Popular brands

Minebea Intec PR 5230, Instrument Manual

Search results

Summary of Contents for PR 5230

Reviews:

Related manuals for PR 5230

Brands by name

Popular brands