Minebea Intec PR 5230 Instrument Manual Download

Page: 256 / 303

10 ModBus protocol

10.1 General description

The ModBus protocol implemented in the instrument permits fast, simple and reliable
communication between a PC or a PLC and up to 127 instruments.

10.2 SPM data in PR 1612 ModBus mode

For access via ModBus, the PR 1612 ModBus mode is switched on via

- [Serial ports]-

[ModBus-RTU]- [Param]- [ModBus mode]- [PR 1612 ModBus].

Read data

Byte address

Weight in 32-bit integer format

Gross weight
Net weight (gross if not tared)
Tare weight (0 if not tared)

Read data

Address

Read "Word" (display in binary format)

W201

0E00000T 00000000

E: ADC error
T: Instrument is tared.

W203

000S00MZ 00000000

S: Device is in setup mode.
M: Weight is stable (standstill).
Z: Weight within ¼ d of 0

W204

0000D000 00000000

D: Gross weight <0 or >Max (dimmed)

W205

TA000000 00000000

T: Instrument is tared.
A: Analog test is active.

W231

00021MRZ 00000000

2: Limit 2
1: Limit 1
M: Weight is stable (standstill).
R: Weight within zero-setting range
Z: Weight within ¼ d of 0

Write data

Bit address

Value in 32-bit integer format

W100

Zero device:
Write value 256

10 ModBus protocol

Transmitter in field housing PR 5230

EN-253

Minebea Intec

Summary of Contents for PR 5230
















































































































































































































































































































Search results

Summary of Contents for PR 5230

Reviews:

Related manuals for PR 5230

Brands by name

Popular brands

Minebea Intec PR 5230, Instrument Manual

Search results

Summary of Contents for PR 5230

Reviews:

Related manuals for PR 5230

Brands by name

Popular brands