Minebea Intec PR 5230 Instrument Manual Download

Page: 32 / 303

Description

Accessories

Ident.

Description

Chapter

Standard

DE1

3 passive (external supply) opto-de-
coupled inputs

4.4.7

Digital inputs

DE2

3 active (internal 12 V supply) opto-de-
coupled inputs

4.4.7

Internal outputs:

Standard

DA1

3 passive relay outputs (external sup-
ply)

4.4.8.1

Digital outputs

DA2

3 passive (external supply) opto-de-
coupled outputs

4.4.8.2

Interface cards:

Standard

None

Interface slot 1

PR 5230/06

C11

1 analog output (0/4

20 mA)

4.6.2

Standard

None

PR 1721/41

C21

ProfiBus-DP

4.6.5

PR 1721/42

C22

InterBus-S

4.6.6

PR 1721/44

C24

DeviceNet

4.6.7

PR 1721/45

C25

CC-Link

4.6.8

PR 1721/46

C26

ProfiNet I/O

4.6.9

Interface slot 2

PR 1721/47

C27

EtherNet IP

4.6.10

Standard

None

Interface slot 3

PR 5230/22

C31

Load cell junction board

4.6.3

Cable connections:

Standard

None

PR 5230/30

M39

Ethernet socket, RJ-45 connector, IP67

4.6.11

For the "Built-in"
Ethernet interface
only:
Connection cable for
network

PR 5230/31

M40

Ethernet cable, 7 m long, metric cable
gland, RJ-45 connector, industry versi-
on

4.6.12

The type identifier (e.g., PR 5230-WE1-Y2-C21-DA2) for the device variant (basic unit +
option) is located on a label inside the door of the device.

3 Device description

Transmitter in field housing PR 5230

EN-29

Minebea Intec

Summary of Contents for PR 5230
















































































































































































































































































































Search results

Summary of Contents for PR 5230

Reviews:

Related manuals for PR 5230

Brands by name

Popular brands

Minebea Intec PR 5230, Instrument Manual

Search results

Summary of Contents for PR 5230

Reviews:

Related manuals for PR 5230

Brands by name

Popular brands