background image

 

1/10/11 
 

FT

DX

5000 Software Update and Version 

Identification 

 

There are four different Software installations. Each one must be followed carefully. Installing the 
wrong type software may cause difficulties. Check your radio before installing software to be sure 
which updates are needed.  
If multiple software installations are required the 

MAIN

 software should be installed first, as it is the 

only one that requires a hard reset (FAST+LOCK).  
 

The latest versions are listed below with the release dates.  

 

MAIN Software Version 

0113

 (1/10/11) 

 

EDSP Software Version 

0529

 (12/17/10) 

 

OEL (OLED) Software Version 

0110

 (3/23/10) 

 

SM-5000 Software Version 

0107

 (3/23/10) 

 

DMU-2000 Software Version (Option): Please refer to the DMU-2000 update information on our 
website.  

 

EDSP-5000 Programming Writer Version 

1.07

 (7/09/10)

 

 

Implements improvements  
 
Main

 Ver. 0113 (1/10/11) 

 

Reduce power off noise from the SM-5000 speaker 

 

EDSP

 Ver. 0529 (12/17/10) 

 

Correct the lock up problem when setting the RX DSP Filter to “SOFT” and the manual Notch 
Filter to ON at the same time. (Default setting is “SHARP”) 

 

EDSP-5000

 Ver. 1.07 (7/09/10) 

 

Extended writer time out.

 

 

We recommend: if you have any previous EDSP 5000 programming writer on your computer, that 
you delete this before using the 

EDSP-5000

 Ver. 

1.07

. Always use the latest version writer.  

 
 
 
 
 
 
 
 
 
 
 
 
  

 

Summary of Contents for FTDX5000 - SOFTWARE UPDATE INFORMATION...











Reviews: