![background image](http://html1.mh-extra.com/html/magnetek/impulse-g-series-4/impulse-g-series-4_instruction-manual_3660463071.webp)
IMPULSE®•G+ & VG+ Series 4 Instruction Manual – February 2017
4-5
Keypad LED and Button Functions
Some of the keypad buttons, whose functions are described below, are dual-purpose. The dual-
purpose keys have one function when used in a view-only mode, and another function when used in
a programming mode.
1
The functions assigned to F1 and F2 vary depending on the current displayed menu. The
name of each function appears in the lower half of the display window.
2
•
Returns to the previous display
•
Moves the cursor one space to the left.
•
Pressing and holding this button will return to the Frequency Reference Display.
3
•
Moves the cursor to the right.
•
Resets the drive to clear a fault situation.
4
Starts the drive when in LOCAL mode.
5
Scrolls up to display the next item, selects parameter numbers, and increments setting
values.
6
Scrolls down to display the previous item, selects parameter numbers, and decrements
setting values.
7
Stops drive operation. *1
8
•
Enters parameter values and settings.
•
Selects a menu item to move between displays.
9
•
Displays the phone number for the Magnetek Service department.
•
Switches drive control between the operator (LOCAL) and an external source
(REMOTE) for the Run command and frequency reference. *2
•
Pressing the key three times resets the maintenance timer, U01-52.
10
Lit while the drive is operating the motor.
Flashing when the drive has a phantom fault.
11
Lit while the operator is selected to run the drive (LOCAL mode).
12
Off during normal operation (no fault or alarm).
Illuminated when the drive detects an alarm or error.
Flashes when an alarm occurs, when an oPE is detected, or when a fault or error occurs
during Auto-Tuning.
*1 The STOP key has highest priority. Pressing the STOP key will always cause the drive to stop the motor, even if a Run command is active at
any external Run command source.
*2 The LO/RE key can only switch between LOCAL and REMOTE when the drive is stopped. To enable the LO/RE key to switch between
LOCAL and REMOTE, set parameter O02-01 to 1.
Summary of Contents for Impulse G+ series 4
