Magnetek Impulse G+ series 4, Instruction Manual

Page: 267 / 276

IMPULSE®•G+ & VG+ Series 4 Instruction Manual – February 2017
A-13
F02-03 AI Input Bias 0.0 -999.9–
999.9
% 5-78
F04-01 AO Ch1 Select 102 1–630 -- 5-79
F04-02 AO Ch1 Gain 100.0 -999.9–
999.9
% 5-79
F04-03 AO Ch2 Select 103 1–630 -- 5-79
F04-04 AO Ch2 Gain 50.0 -999.9–
999.9
% 5-79
F04-05 AO Ch1 Bias 0.0 -999.9–
999.9
% 5-79
F04-06 AO Ch2 Bias 0.0 -999.9–
999.9
% 5-79
F04-07 AO Opt Level Ch1 0 0, 1 -- 5-79
F04-08 AO Opt Level Ch2 0 0, 1 -- 5-79
F05-01 DO Ch1 Select F 0–148 -- 5-80
F05-02 DO Ch2 Select F 0–148 -- 5-80
F05-03 DO Ch3 Select F 0–148 -- 5-80
F05-04 DO Ch4 Select F 0–148 -- 5-80
F05-05 DO Ch5 Select F 0–148 -- 5-80
F05-06 DO Ch6 Select F 0–148 -- 5-80
F05-07 DO Ch7 Select F 0–148 -- 5-80
F05-08 DO Ch8 Select F 0–148 -- 5-80
F05-09 DO Function Sel 2 0–2 -- 5-80
F06-01 Comm Bus Flt Sel 1 0–4 -- 5-82
F06-02 EF0 Detection 0 0, 1 -- 5-82
F06-03 EF0 Fault Action 1 0–4 -- 5-82
F06-04 BUS Err Det Time 2.0 0.0–5.0 sec 5-82
F06-06 Torq Ref/Lmt Sel 0 0, 1 -- 5-82
F06-07 Fref PrioritySel 0 0, 1 -- 5-82
F06-08 Com Prm Init Sel 0 0, 1 -- 5-82
F06-30 PB Node Address 0 0–125 -- 5-82
F06-31 PB Clear Select 0 0, 1 -- 5-83
F06-32 PB Map Select 0 0, 1 -- 5-83
F06-35 CO Node Address 0 0–126 -- 5-83
F06-36 CO Baud Rate 6 0–8 -- 5-83
F06-50 DN MAC Address 64 0–64 -- 5-83
F06-51 DN Baud Rate 4 0–4 -- 5-83
F06-52 DN PCA Selection 21 0–225 -- 5-83
F06-53 DN PPA Selection 71 0–225 -- 5-83
F06-54 DN Idle Flt Det 0 0, 1 -- 5-83
F06-55 DN BAUD RATE MEM 0 0–2 -- 5-84
F06-56 DN Speed Scale 0 -15–15 -- 5-84
F06-57 DN Current Scale 0 -15–15 -- 5-84
Parameter Parameter Name Default Range Units Reference
* Initial value set by X-Press Programming (Table 4-6, 4-7, or 4-8 on pages 4-12, 4-13, and 4-14).
** Initial value dependent on drive size, which is determined by O02-04 (kVA Selection).
*** Value is automatically set during auto tuning.
**** 0.0–25.5 seconds is extended to 0.0–6000.0 seconds when B05-16 = 1.