![background image](http://html1.mh-extra.com/html/magnetek/impulse-g-series-4/impulse-g-series-4_instruction-manual_3660463249.webp)
IMPULSE®•G+ & VG+ Series 4 Instruction Manual – February 2017
6-27
oFC01
A1-A3
AO-A3
DI-A3
DO-A3
S4I
S4IO
Option connection error
at drive port CN5-C.
• Option at drive port
CN5-C was changed
during run.
• Turn off the power and
check the connectors
between the drive and
the option.
oFC02
A1-A3
AO-A3
DI-A3
DO-A3
S4I
S4IO
Option Fault (CN5-C).
Two of the same option
cards are connected
simultaneously.
• AI-A3: AI-A3 option
connected to CN5-B
port while another input
option was connected
to CN5-A port.
• DI-A3: DI-A3 option
connected to CN5-B
port while another input
option was connected
to CN5-A port.
• AO-A3/DO-A3:
Duplicate type of
option card is
connected to drive
ports CN5-A, CN5-B,
and CN5-C.
• AI-A3: Only one of the
options, AI-A3, DI-A3,
or SI-xx can be
connected to the drive
at the same time.
• DI-A3: Only one of the
options, AI-A3, DI-A3,
or SI-xx can be
connected to the drive
at the same time.
• AO-A3/DO-A3: Use
only compatible
options.
oFC03
to
oFC11
A1-A3
AO-A3
DI-A3
DO-A3
S4I
S4IO
Option Card Fault at
Option Port CN5-C.
• Option card or
hardware is damaged.
• Cycle power to the
drive
• If the problem
continues, replace the
control board or the
entire drive. Contact
Magnetek for
instructions on
replacing the control
board.
oFC12
to
oFC17
A1-A3
AO-A3
DI-A3
DO-A3
S4I
S4IO
Option Card Fault at
Option Port CN5-C.
• Option card or
hardware is damaged.
• Cycle power to the
drive
• If the problem
continues, replace the
control board or the
entire drive. Contact
Magnetek for
instructions on
replacing the control
board.
oPE05
A1-A3
DI-A3
S4I
S4IO
Run command/frequency
reference source
selection error.
• Frequency reference is
assigned to an option
(B03-01 = 3), but an
option is not
connected.
• Reconnect the option
to the drive.
oPE06
--
Control Method Selection
Error
• A control mode has
been selected that
requires a PG option
card to be installed, but
no PG encoder is
installed (A01-02 = 1 or
3).
• Connect to a PG option
card.
• Correct the value set to
A01-02.
Error
Card
Fault or Indicator
Name/Description
Cause
Possible Solution
Summary of Contents for Impulse G+ series 4
