MacDon M205 2012, Operator'S Manual, Page: 60 / 230

OPERATOR’S STATION
169469/169470/169471
58
Revision E
L1 C x x x || A C T I V A T E H Y D P U R G E ?
L2 X x x x || N O / Y E S
L1 C x x x || T O A C T I V A T E P U R G E
L2 X x x x || P R E S S A N D H O L D
L1 C x x x || P U R G E C Y C L E S T A R T E D
L2 X x x x || P R E S S A N D H O L D
L1 C x x x || P U R G E C Y C L E E N D E D
L2 X x x x ||
L1 C x x x || P U R G E C Y C L E E N D E D
L2 X x x x || N O E X I T Y E S T O A C T I V A T E P U R G E
L1 C x x x || E X I T F U N C T I O N M E N U ?
L2 X x x x || N O / Y E S A C T I V A T E H E A D E R H T
L1 C x x x || F O R C E H E A D E R T Y P E ?
L2 X x x x || N O / Y E S E X I T D I A G N O S T I C S ?
L1 C x x x || S E L E C T H E A D E R T Y P E
L2 X x x x || D I S K H E A D E R
L2 X x x x || S K A U G E R
L2 X x x x || D K A U G E R
L2 X x x x || G R A S S S E E D
L2 X x x x || 2 0 F T S K D R A P E R
L2 X x x x || 2 5 F T S K D R A P E R
L2 X x x x || 3 0 F T S K D R A P E R
W
L2 X x x x || 3 5 F T S K D R A P E R
L2 X x x x || 1 5 F T D K D R A P E R
L2 X x x x || 2 0 F T D K D R A P E R
L2 X x x x || 2 5 F T D K D R A P E R
L2 X x x x || 3 0 F T D K D R A P E R
L2 X x x x || 3 5 F T D K D R A P E R
L2 X x x x || 4 0 F T D K D R A P E R
L1 C x x x || E X I T F O R C E H E A D E R ?
L2 X x x x || N O / Y E S S E L E C T H E A D E R T Y P E
L1 C x x x || E X I T D I A G N O S T I C ?
L2 X x x x || N O / Y E S V I E W E R R O R C O D E S
L1 C x x x || E X I T S E T U P ?
L2 X x x x || N O / Y E S W I N D R O W E R S E T U P ?
O P E R A T I N G S C R E E N S
If “NO” then jump to:
If “NO” then jump to:
When “SELECT” is pressed the program goes
to the EXIT HEADER TYPE? menu selection.
This allows the operator to select or “force” a
header ID configuration if a “NO HEADER” ID
is being read by the control system. The
header type will revert back to “NO HEADER”
every time the ignition is cycled.
If “NO” then jump to:
If “NO” then jump to:
If “YES” then jump to:
If “NO” then jump to:
If “NO” then jump to:
Pressing and holding the right hand “arrow” button
activates a predetermined timed purge cycle.
Releasing pressure on the switch or a completed
cycle (timed out) will jump to the PURGE CYCLE
ENDED menu selection.
ACTIVATE HYD PURGE - This is to allow the
operator to purge the air from a new or changed
pump system.