background image

WINDROWER OPERATION 

 

169469/169470/169471

 

76

 

Revision E

 

6.3.8 TRANSPORTING 

6.3.8.1 

Driving On Road 

The M205 Windrower is designed to be driven on 
the road with the engine-forward to provide better 
visibility for the Operator, and improved stability 
for the machine. Refer to Section 6.3.6.3 
Engine-forward Operation. The windrowers are 
capable of being driven on the road in 

 

cab-forward, but at a reduced speed and under 
restricted conditions. 

WARNING 

Collision between windrower and other 
vehicles may result in injury or death. 

WARNING 

When driving windrower on public roadways: 

 

Obey all highway traffic regulations in your 
area. Use pilot vehicles front and rear of 
windrower if required by law. 

 

Use slow moving vehicle emblem and 
flashing warning lights unless prohibited 
by law. 

 

If width of attached header impedes other 
vehicle traffic, remove header, and install a 
MacDon approved weight box. 

CAUTION 

Check local laws for width regulations, 
lighting, and marking requirements before 
transporting on roads. 

WARNING 

 

Do not drive windrower on the road in the 
cab-forward mode, unless the optional 
lighting marking kit is installed, as 
lighting/reflector visibility will not be 
compliant with road regulations. See 
Section 5.7.3.     

 

Do not drive windrower on a road or 
highway at night, or in conditions which 
reduce visibility, such as fog or rain. The 
width of the windrower may not be 
apparent under these conditions. 

CAUTION 

Operate both steering wheel and ground speed 
lever slowly for familiarization. Remember that 
steering is more sensitive when speed-range 
control is in ROAD SPEED position. Avoid the 
common tendency of new Operators to 
over-steer. 

a.  Ensure HEADER DRIVE switch is pushed to OFF 

position. 

b.  Before driving windrower on a roadway: 

1.  Clean flashing amber lamps, red tail lamp and 

head lamps, and check that they work 
properly. 

2.  Clean all reflective surfaces and slow moving 

vehicle emblems.  

3.  Adjust interior rear view mirror, and clean 

windows. 

(continued next page) 

HEADER DRIVE 

ON-OFF 

Summary of Contents for M205 2012







































































































































































































































Reviews: