Kverneland Vicon RF 2235 Operating Manual Download

Page: 118 / 135

118

Accessories

Hitch-drawbar eye

When the tractor is equipped with a hitch hook, the drawbar must be

equipped with a draw hook.

Dummy blades for

OptiCut

For a variable use of the implement, the knives can be replaced with

dummy blades to change the cutting length. It is necessary to fit the

dummy blades so that the crop is fed in uniformly.

Dummy blades are fitted in the same way as the knives.

→

See »Removing the knives« and »Fitting the knives«, page 51.

→

See »Removing the knives« and »Fitting the knives«, page 54.

Roller for baffle

plate

The baffle plate roller improves the way the crop is fed in. The roller

will be fitted on the front baffle plate support (as shown).

Hitch-draw-

Dummy blade

Roller for baffle plate

All manuals and user guides at all-guides.com

Summary of Contents for Vicon RF 2235








































































































































Search results

Summary of Contents for Vicon RF 2235

Reviews:

Related manuals for Vicon RF 2235

Brands by name

Popular brands

Kverneland Vicon RF 2235, Operating Manual

Search results

Summary of Contents for Vicon RF 2235

Reviews:

Related manuals for Vicon RF 2235

Brands by name

Popular brands