Kverneland Vicon RF 2235 Operating Manual Download

Page: 97 / 135

Maintenance

Chain lubrication

When the implement is equipped with the “automatic chain lubrication

[+]” supplementary equipment, the chains will be supplied with the cor-

rect amount of oil by this system. The oil level in the reservoir must be

checked every day.

In the absence of this supplementary equipment, the bale chamber

chains must be lubricated with chain lubricant several times a day or

every 200 bales, depending on which occurs first.

Filling

> Open the left-hand side door.

> Check the oil level.

> Fill the oil level up to 3.5 litres maximum.

> Close the left-hand side door.

Adjusting the oil

pump

> Release the nuts on the washer disc.

> Turn the washer disc:

•

Clockwise to increase the conveying capacity.

•

Counter-clockwise to reduce the conveying capacity.

> Tighten the nuts on the washer disc.

Oil reser-

voir

Oil pump

Washer disc

Grease / Oil

Specification

Oil,

SAE 30 BIO oil

Oil pump

Washer disc

All manuals and user guides at all-guides.com

Summary of Contents for Vicon RF 2235








































































































































Search results

Summary of Contents for Vicon RF 2235

Reviews:

Related manuals for Vicon RF 2235

Brands by name

Popular brands

Kverneland Vicon RF 2235, Operating Manual

Search results

Summary of Contents for Vicon RF 2235

Reviews:

Related manuals for Vicon RF 2235

Brands by name

Popular brands