Kverneland Vicon RF 2235 Operating Manual Download

Page: 40 / 135

Hitching the implement

Electricity supply

AutoPlus control electricity supply

The cable should under no circumstances be supplied with power by

the cigarette lighter. The power must always be supplied via the 3-pin

12 V plug (DIN 9680). The condition of the fuse in the power cable

must be checked. There is a risk of electrical power cuts and mal-

functions.
The AutoPlus-Pilotbox must be fitted in an easily accessible position

within the tractor cabin.
Please note the following:

•

Ensure that the tractor operator can easily activate the AutoPlus-

Pilotbox and easily read the LCD.

•

Wherever possible, the AutoPlus-Pilotbox should be fitted where

the vibration from the tractor is at its weakest.

•

Wherever possible, the AutoPlus-Pilotbox should be fitted where

there is the least risk of dust.

•

Protect the AutoPlus-Pilotbox from direct sunlight or moisture.

Check the cable routing

Check the cable routing. The cable must shown no signs of abrasion

or sagging. Torn or frayed cables can cause unforeseen movements

on the implement.
Attach the following electrical cables to the tractor:

Lighting

•

Lighting of the implement.

> Connect the plug for the 12-V power supply to the 7-pin plug socket

on the tractor.

AutoPlus- Pilotbox

•

Power supply to the AutoPlus-Pilotbox

> Connect the plug for the 12 V power supply to the 3-pin plug socket

on the tractor.

Alternative

connector cable

For owners of tractors for which no 3-pin 12-V connection is available,

an alternative cable for the AutoPlus control box power supply is pro-

vided.

> The alternative cable [+] for the AutoPlus control box is directly

connected to the tractor 12-V battery.

Battery

Cable

Blue

Brown

Colour Pole

Brown

Blue

All manuals and user guides at all-guides.com

Summary of Contents for Vicon RF 2235








































































































































Search results

Summary of Contents for Vicon RF 2235

Reviews:

Related manuals for Vicon RF 2235

Brands by name

Popular brands

Kverneland Vicon RF 2235, Operating Manual

Search results

Summary of Contents for Vicon RF 2235

Reviews:

Related manuals for Vicon RF 2235

Brands by name

Popular brands