manualshive.com logo in svg

Kverneland Vicon RF 2235, Operating Manual

Share
Download
Kverneland Vicon RF 2235 Operating Manual Download Page 126

126

Eliminating malfunctions

Malfunctions

Malfunctions can often be eliminated quickly and easily. Before calling

Customer Service, refer to the table to check whether the malfunction

is one you can eliminate yourself.

AutoPlus-Pilotbox

Electronics

Problem

Cause

Solution

Low battery voltage.

> The battery voltage is under 9 

volts. Check the tractor's power 

supply.

Twine malfunction. The twine wrap-

ping does not start.

> Open the front hood and check 

the twine guide and sensors. 

> After clearing the fault, press 

the “GO” button.

Net malfunction. The net wrapping

does not run.

> Open the front hood and check 

the net, net guide and sensors. 

> After clearing the fault, press 

the “GO” button.

Net motor malfunction. The net mo-

tor does not run.

> Open the front hood and check 

the connections. 

> After clearing the fault, press 

the “GO” button. 

> If the fault cannot be cleared, 

contact customer services.

> The net was drawn in at the 

wrong moment.

> Open the front hood and check 

the net, net guide and sensors. 

> After clearing the fault, press 

the “GO” button.

Problem

Cause

Solution

No display on the AutoPlus-Pilot-

box

The control unit has no power

•

Switch on the device

•

Check the system's power sup-

ply

•

Check the fuses in the Au-

toPlus control box

Internal control system problem

Please contact your supplier

All manuals and user guides at all-guides.com

all-guides.com

Summary of Contents for Vicon RF 2235








































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands