Kverneland Vicon RF 2235 Operating Manual Download

Page: 19 / 135

Safety

The tractor's PTO shaft continues turning after it has been swit-

ched off

After the tractor's PTO shaft has been unhitched or disconnected the

implement continues running due to inertia. Maintain a safe distance

until the pick-up equipment and all moving parts have come to a com-

plete standstill.
Cornering and turning manoeuvres

Centrifugal forces are in operation when cornering. The implement's

centre of gravity at the rear of the tractor is displaced. Be aware of the

turning radius and the moment of inertia. A driving style which is not

adapted to conditions can cause accidents. The consequence can be

accidents with serious or fatal injuries.
Bale ejection

Stay away from the bale ejection area. There is a risk of crushing. ne-

ver stand behind the implement when a bale is being ejected. Ensure

that no other persons are positioned behind the implement. There is

otherwise the risk of serious or fatal injury.
Observe the field conditions

Proceed with the utmost caution on hilly terrain or shifting subsoil.

Keep to both the maximum permissible engine load and the gross

working weight limit. A driving style which is not adapted to conditions

can cause accidents. The consequence can be accidents with serious

or fatal injuries.
Obstruction by a safety device

If there is a blockage or if a safety device is triggered, only operate on

the implement after following the instructions below:

•

Switch off the tractor's PTO shaft.

•

Switch off the electronic control system.

•

Switch off the engine and take out the ignition key.

Never try to repair a blockage or a malfunction on the implement ma-

nually during operation. There is otherwise the risk of serious or fatal

injury.

All manuals and user guides at all-guides.com

Summary of Contents for Vicon RF 2235








































































































































Search results

Summary of Contents for Vicon RF 2235

Reviews:

Related manuals for Vicon RF 2235

Brands by name

Popular brands

Kverneland Vicon RF 2235, Operating Manual

Search results

Summary of Contents for Vicon RF 2235

Reviews:

Related manuals for Vicon RF 2235

Brands by name

Popular brands