Kverneland Vicon RF 2235 Operating Manual Download

Page: 132 / 135

132

Environmental protection

At the end of the implement's service life, the individual components

must be disposed of in a correct and environmentally-friendly manner.

Please observe the currently valid national waste disposal guidelines.
Plastic parts

Plastic parts can be disposed of in the normal household waste (resi-

dual waste), depending on the laws specific to your country.
Metal parts

All metal parts can be disposed of in the used metal recycling system.
Oil,

Environmentally-compatible hydraulic oils must be stored, collected

and disposed of separately in accordance with waste legislation.
Electronics

The AutoPlus-Pilotbox and control box must be taken to a special wa-

ste disposal firm.

All manuals and user guides at all-guides.com

Summary of Contents for Vicon RF 2235








































































































































Search results

Summary of Contents for Vicon RF 2235

Reviews:

Related manuals for Vicon RF 2235

Brands by name

Popular brands

Kverneland Vicon RF 2235, Operating Manual

Search results

Summary of Contents for Vicon RF 2235

Reviews:

Related manuals for Vicon RF 2235

Brands by name

Popular brands