Kverneland Vicon RF 2235 Operating Manual Download

Page: 48 / 135

Preparing for use

Adjusting the pick-

up equipment

The pick-up equipment adjusts the ground pressure using two springs

on the hydraulic cylinders, to ensure that the crop is gathered correct-

ly. The safety plate can be placed in four positions, to enable different

pick-up equipment setting gradients.
The spring tension on both sides of the pick-up equipment is adjusted

as follows:

> Switch the tractor on.

Switch on the AutoPlus-Pilotbox.
> Press the “ON/OFF” button.

> Press the “INFO” button...

> ...until the “Pick-up/Knives” symbol is displayed.

> Raise the pick-up equipment via the control device.

Switch off the AutoPlus-Pilotbox.
> Press the “ON/OFF” button.

> Switch off the tractor and secure it.

> Close the ball valve.

> Slide the safety plate in the direction of motion: The spring tension

is increased. The pick-up of the crop is more gentle.

> Slide the safety plate towards the rear: The spring tension is redu-

ced. The pick-up of the crop is more aggressive.

> Open the ball valve.

> Switch the tractor on.

> Raise the pick-up equipment via the control device.

OTE

Ensure that the spring tension on both sides of the pick-up equipment

is identical.

Safety plate

Open

Closed

All manuals and user guides at all-guides.com

Summary of Contents for Vicon RF 2235








































































































































Search results

Summary of Contents for Vicon RF 2235

Reviews:

Related manuals for Vicon RF 2235

Brands by name

Popular brands

Kverneland Vicon RF 2235, Operating Manual

Search results

Summary of Contents for Vicon RF 2235

Reviews:

Related manuals for Vicon RF 2235

Brands by name

Popular brands