Kverneland Vicon RF 2235 Operating Manual Download

Page: 78 / 135

Operation

Manual

tying

For manual tying, a signal is emitted by the AutoPlus-Pilotbox when

the preset bale density is reached. A filling level of 90% is displayed

on the AutoPlus-Pilotbox at the same time. As soon as 100% bale

density is reached, proceed as follows:
> The AutoPlus-Pilotbox signal sounds.

> “Bale density 90%” is displayed.

> “Bale density 100%” is displayed.

> Stop the tractor immediately.

> Press the “GO” button. Net or twine tying is triggered and the signal

stops.

> The display shows “tying start” during bale wrapping.

> The display shows “Open rear flap” after successful bale wrapping

and cutting of the tying material.

> The AutoPlus-Pilotbox signal sounds.

> Carry out the »Depositing the bale« operating instructions, page

79.

OTE

These operating instructions are also applicable for twine tying.

All manuals and user guides at all-guides.com

Summary of Contents for Vicon RF 2235








































































































































Search results

Summary of Contents for Vicon RF 2235

Reviews:

Related manuals for Vicon RF 2235

Brands by name

Popular brands

Kverneland Vicon RF 2235, Operating Manual

Search results

Summary of Contents for Vicon RF 2235

Reviews:

Related manuals for Vicon RF 2235

Brands by name

Popular brands