Kverneland Vicon RF 2235 Operating Manual Download Page 69

Page: 69 / 135

Driving on the road

Road travel

check list

Prior to driving on the road check the implement against this check list:

•

Rear flap completely closed?

•

AutoPlus-Pilotbox off?

•

Tractor control device in the neutral position?

•

Tractor's PTO operation off?

•

Stop valves closed?

•

Tyre pressure correct?

•

Remaining crop and coarse dirt removed?

•

Lighting operating?

•

Load-dependent brake set to the “Full load” position?

•

Brake system correctly connected and checked?

•

Are the cables, ropes and lines routed so that they are not straining

and cannot interfere with the tractor's wheels when cornering?

Road transport

•

Before starting off, check the immediate vicinity. Always ensure

that there is an unimpeded view and pay particular attention to any

children in the vicinity of the implement.

•

Do not transport any personnel or objects on the implement.

•

Always adjust your driving speed to the road conditions.

•

Do not exceed a maximum speed of 40 km/h. Comply with the na-

tional speed limits.

•

Ensure sufficient steering and braking capability. Driving beha-

viour, steering and braking capability are influenced by the imple-

ment that is coupled (longer braking distances due to greater

thrust).

•

There is a danger of tipping in precipitous places and if corners are

taken too fast.

All manuals and user guides at all-guides.com

Summary of Contents for Vicon RF 2235








































































































































Search results

Summary of Contents for Vicon RF 2235

Reviews:

Brands by name

Popular brands

Kverneland Vicon RF 2235, Operating Manual

Search results

Summary of Contents for Vicon RF 2235

Reviews:

Brands by name

Popular brands