Kverneland Vicon RF 2235 Operating Manual Download

Page: 26 / 135

Familiarise yourself with the device

Load-dependent

brake [+]

Load-dependent brake during road travel

Always set the load-dependent brake to the “full load” brake power du-

ring road travel. Otherwise there is reduced brake power. There is

otherwise the risk of traffic accidents and accidents with fatal conse-

quences.
Load-dependent brake on hilly terrain

Always set the load-dependent brake to the “full load” brake power

when travelling on hilly terrain. Otherwise there is reduced brake po-

wer. The consequence can be serious accidents.

Adjusting the load-dependent brake in field use

The optional load-dependent compressed-air brake is used to adjust

the braking force of the implement to the actual weight of the load, and

is triggered accordingly. Optimum deceleration is achieved in this

way. The following settings can be made using the brake lever on the

brake valve:

•

Full load:

Setting for road transport.

•

Half load:

Setting for field use.

This function protects the stubble.

•

Empty:

Setting for field use.

This function protects the stubble.

•

Released:

Brake released.

The implement can be stored.

OTE

If the bale chamber becomes full of silage, the braking load should be

set to “Full load”. Otherwise reduced brake power must be anticipated.

OTE

Adjusting the braking force correctly protects the stubble.

Half load

Full load

Release

Brake lever

Empty

Brake valve

All manuals and user guides at all-guides.com

all-guides.com

Summary of Contents for Vicon RF 2235








































































































































Search results

Summary of Contents for Vicon RF 2235

Reviews:

Related manuals for Vicon RF 2235

Brands by name

Popular brands

Kverneland Vicon RF 2235, Operating Manual

Search results

Summary of Contents for Vicon RF 2235

Reviews:

Related manuals for Vicon RF 2235

Brands by name

Popular brands