Kverneland Vicon RF 2235 Operating Manual Download

Page: 105 / 135

Maintenance

105

Adjusting the net

wrapping

V-belt for the net

drive mechanism

When carrying out regular maintenance, the V-belt tension for the net

roller must be checked.

•

Excessive belt tensioning: The net is drawn in during bale produc-

tion.

•

Low belt tensioning: Net wrapping does not operate.

> Loosening the V-belt-idler pulley.

The V-belt is slack.

> Loosen and remove the screw on the belt pulley.

> Remove the belt pulley.

> Fit or remove the filling discs between the belt pulleys.

•

Several filling discs: reduced belt tension.

•

Few or no filling discs: high belt tension.

> Refit the belt pulley.

> Fit and tighten the belt pulley screws.

> Tension the V-belt-idler pulley.

Net feed roller

tension

The contact pressure on the net feed roller is provided by two springs.

The springs are located on the left and right of the net feed roller and

are secured with a screw. The spring tension for the net rollers can be

changed by moving the screw in the oval hole.
> Loosen the screw and the nut.

> Move the screw to the desired position.

> Fit and tighten the screw.

Belt pulley

Filling disc

V-belt-idler

pulley

Spring

Screw

Oval hole

All manuals and user guides at all-guides.com

Summary of Contents for Vicon RF 2235








































































































































Search results

Summary of Contents for Vicon RF 2235

Reviews:

Related manuals for Vicon RF 2235

Brands by name

Popular brands

Kverneland Vicon RF 2235, Operating Manual

Search results

Summary of Contents for Vicon RF 2235

Reviews:

Related manuals for Vicon RF 2235

Brands by name

Popular brands