Kverneland Vicon RF 2235 Operating Manual Download

Page: 73 / 135

Operation

Safety

Observe safety instructions

Observe the safety instructions for the performance of all work. Any

disregard for safety instructions can lead to serious or fatal injuries to

persons.
No riding on the implement

Neither personnel nor objects are allowed to be transported on the im-

plement at any time. Riding on the implement is hazardous and strictly

prohibited. There is otherwise the risk of serious or fatal injury.
There should be no personnel standing in the working area

No-one is permitted to remain within the working area. Personnel can

be caught by the implement. There is otherwise the risk of serious or

fatal injury.
Maximum cardan shaft speed 540 rpm

The cardan shaft speed must not exceed 540 rpm and has to be ad-

apted to the condition of the crop. Higher speeds can cause damage

to the implement.
Do not upset the cardan shaft

The cardan shaft between the tractor and implement must not be jol-

ted in any operating or transport position. Upset cardan shafts can

cause damage to the implement and tractor.
Note the contour of the terrain

Pay even more attention when driving on an incline. Avoid inclines on

which the combination (tractor and implement) could slip or overturn.

There is an increased risk of tipping and injury if the implement is

towed in a direction offset in relation to the direction of the slope.

All manuals and user guides at all-guides.com

Summary of Contents for Vicon RF 2235








































































































































Search results

Summary of Contents for Vicon RF 2235

Reviews:

Related manuals for Vicon RF 2235

Brands by name

Popular brands

Kverneland Vicon RF 2235, Operating Manual

Search results

Summary of Contents for Vicon RF 2235

Reviews:

Related manuals for Vicon RF 2235

Brands by name

Popular brands