Kverneland Vicon RF 2235 Operating Manual Download

Page: 86 / 135

Maintenance

Safety

The following applies to all servicing work:
Observe safety instructions

Observe the safety instructions for the performance of all work. Any

disregard for safety instructions can lead to serious or fatal injuries to

persons.
Prerequisites for maintenance work

Only perform the maintenance operations if you have the required ex-

pert knowledge and suitable tools. The absence of technical know-

ledge or suitable tools can cause accidents and injuries.
Use

OEM (original equipment manufacturers) replacement parts

Many components have special properties that are decisive for the

stability and operability of the implement. Only spare and wear parts

supplied by the manufacturer have been tested and cleared. Using

other products may lead to malfunctions or reduce safety of operation.

The use of non-OEM replacement parts renders the manufacturer's

guarantee null and void and frees the manufacturer from all liability.
Protect the device from unintended start-up

The following conditions must be observed for carrying out repairs and

maintenance work and rectifying malfunctions on the coupled imple-

ment:

•

Switch off the tractor's PTO shaft.

•

Switch off the AutoPlus-Pilotbox.

•

Switch off the tractor engine.

•

Take out the ignition key.

Severe accidents can result if the device starts inadvertently.

All manuals and user guides at all-guides.com

all-guides.com

Summary of Contents for Vicon RF 2235








































































































































Search results

Summary of Contents for Vicon RF 2235

Reviews:

Related manuals for Vicon RF 2235

Brands by name

Popular brands

Kverneland Vicon RF 2235, Operating Manual

Search results

Summary of Contents for Vicon RF 2235

Reviews:

Related manuals for Vicon RF 2235

Brands by name

Popular brands