Kverneland Vicon RF 2235 Operating Manual Download

Page: 110 / 135

110

Maintenance

Drawbar

Securing moving parts

Moving parts must be secured with lifting gear against sliding, folding

or swivelling. Personnel may be injured or the implement may be da-

maged as a result.

Adjusting the

drawbar

The drawbar and drawbar eye can rotate through 180°. In this way, the

drawbar can be adjusted for a high or low hitch.
The implement must be positioned horizontally:

> Turn the crank anti-clockwise: Move the drawbar upwards.

> Turn the crank clockwise: Move the drawbar downwards.

> Check the height of the tractor's draw hook.

> Secure the drawbar against sliding.

> Loosen and remove the screws and nuts.

> Move the drawbar to the desired position

> Fit and tighten the screws and nuts.

→

»Special torques«, page 91.

> Remove the safety device preventing sliding.

The arrangement of holes on the implement is provided for height ad-

justment. The drawbar must always be secured on each side with two

screws and nuts.

Trailer ring

A bush is located on the trailer ring of the drawbar eye; this must be

replaced when it is visibly worn.

> Before the season and after every 500 bales, the underside of the

trailer ring must be lubricated.

Swivelling drawbar

eye

> Lubricate the swivelling drawbar eye with oil.

Drawbar

Drawbar eye

Crank

Nuts

Screws

Drawbar

Oil,

All manuals and user guides at all-guides.com

Summary of Contents for Vicon RF 2235








































































































































Search results

Summary of Contents for Vicon RF 2235

Reviews:

Related manuals for Vicon RF 2235

Brands by name

Popular brands

Kverneland Vicon RF 2235, Operating Manual

Search results

Summary of Contents for Vicon RF 2235

Reviews:

Related manuals for Vicon RF 2235

Brands by name

Popular brands