Kverneland Vicon RF 2235 Operating Manual Download

Page: 46 / 135

Preparing for use

General

conditions

The following applies for all preliminary provisions:

•

Secure the tractor and the implement.

•

Check the tyre pressure.

Before commissioning the implement, the following work steps must

be carried out, as described in this chapter:

•

Open the rear flap.

•

Close the rear flap.

•

Adjust the roller feelers.

•

Adjust the pick-up equipment.

•

Adjust the OptiCut cutterbar.

•

Insert the twine.

•

Insert the net.

•

Adjust the bale density.

•

Adjust the scraper.

Opening the rear flap

> Open the rear flap via the control device.

Switch off the AutoPlus-Pilotbox.
> Press the “ON/OFF” button.

> Switch off the tractor, take out the ignition key and secure it.

> Close the rear flap hydraulic manifold ball valve. The hydraulic ma-

nifold is located between the drawbar. When closed, the open rear

flap is secured.

Closing the rear flap

> Open the rear flap hydraulic manifold ball valve . When open, the

rear flap is no longer secured and can be closed.

> Switch the tractor on.

Switch on the AutoPlus-Pilotbox.
> Press the “ON/OFF” button.

> Close the rear flap via the control device.

> Leave the control device lever in rear flap closed position for appro-

ximately 3 seconds, to build up the pressure for the default bale

density.

Rear flap ball

valve

Rear flap ball

valve

All manuals and user guides at all-guides.com

all-guides.com

Summary of Contents for Vicon RF 2235








































































































































Search results

Summary of Contents for Vicon RF 2235

Reviews:

Related manuals for Vicon RF 2235

Brands by name

Popular brands

Kverneland Vicon RF 2235, Operating Manual

Search results

Summary of Contents for Vicon RF 2235

Reviews:

Related manuals for Vicon RF 2235

Brands by name

Popular brands