Kverneland Vicon RF 2235 Operating Manual Download Page 42

Page: 42 / 135

Hitching the implement

Hydraulic

connections

Hydraulic

connections

Hydraulic connection at zero pressure only

Only connect hydraulic tubes to the tractor hydraulic system if the trac-

tor and implement hydraulic system is at zero pressure. A pressurised

hydraulic system can trigger unforeseen movements on the imple-

ment and can cause serious damage and injuries. There is otherwise

the risk of serious or fatal injury.
Avoid oil mixtures

If the implement is used on different tractors, an unauthorised oil mix-

ture may occur. Non-allowed oil mixtures can destroy components on

the tractor.
Clean hydraulic system

Remove any dirt which has entered the hydraulic system. The hydrau-

lic system can be seriously damaged. Material damage and injuries to

personnel may be caused.
Check tubes and couplings

Check all hydraulic tubes for damage before connecting them. Check

all hydraulic couplings for firm seating after connecting them. Defecti-

ve hydraulic tubes or incorrectly positioned hydraulic couplings can

cause the implement to move unexpectedly and may cause serious

damage to personnel or the implement. There is otherwise the risk of

serious or fatal injury.
Secure the control devices

In transport position, secure the control devices on the tractor against

unintended actuation and lock if possible. Unintended actuation of the

control device can cause the implement to move unexpectedly and

may cause serious damage to personnel or the implement. There is

otherwise the risk of serious or fatal injury.
Check that the hydraulic tubes are correctly positioned

Ensure that the hydraulic tubes are not caught, pinched or trapped.

Ensure there is ample free space. Hydraulic tubes which are damaged

or entangled with other components can cause the implement to move

unexpectedly and uncontrollably and may cause serious damage to

personnel or the implement. There is otherwise the risk of serious or

fatal injury.

All manuals and user guides at all-guides.com

Summary of Contents for Vicon RF 2235








































































































































Search results

Summary of Contents for Vicon RF 2235

Reviews:

Brands by name

Popular brands

Kverneland Vicon RF 2235, Operating Manual

Search results

Summary of Contents for Vicon RF 2235

Reviews:

Brands by name

Popular brands