Kverneland Vicon RF 2235 Operating Manual Download

Page: 11 / 135

Safety

Secure the implement with wheel chocks

Always secure the implement in the park and stop position with wheel

chocks to ensure it cannot roll away. Serious or fatal injury can be the

result.

Avoid the danger zone around the cardan shaft

Stay well outside of the danger zone around the cardan shaft. Do not

use the cardan shaft if the protective guard is damaged or defective.

This could otherwise result in serious injury.

Distance from the pick-up equipment

Remain a safe distance away from the rotating pick-up equipment.

You may be caught by the rotating tines and pulled into the implement.

Serious or fatal injury can be the result.

Distance from the tractor

When the implement is being coupled, uncoupled or operated, there

should be no-one causing an obstruction between the tractor and the

implement. Serious or fatal injury can be the result.

Distance from the closed rear flap

Maintain a safe distance from the closed rear flap. The rear flap may

open by itself. Serious or fatal injury can be the result.

All manuals and user guides at all-guides.com

all-guides.com

Summary of Contents for Vicon RF 2235








































































































































Search results

Summary of Contents for Vicon RF 2235

Reviews:

Related manuals for Vicon RF 2235

Brands by name

Popular brands

Kverneland Vicon RF 2235, Operating Manual

Search results

Summary of Contents for Vicon RF 2235

Reviews:

Related manuals for Vicon RF 2235

Brands by name

Popular brands