background image

System configuration information 

14 / 156 

 

3.1.3  Current allocation on multiple vehicles 

The allocation of quotas follows the FIFO principle (First-in-First out), the charging current quotas for Mode 3 
charging and ISO charging will be considered separately. 
 

 

 
 

Section ISO charging 

If the total charging current of the EVs in the ISO charging group exceeds the limit, a new added vehicle (in 
the example "ISO4") will not be charged immediately. The vehicle "ISO4" is shifted for a later moment, until 
the consumption of the other EVs in the ISO group is going down and a quota is available. 
 

Section Mode 3 charging 

If  the total charging current of the EVs in the Mode 3 charging group exceeds the limit, a new added vehicle 
(in the example “M3-1”) can be charged anyway, if there is a free quota in the ISO charging group. The vehi-
cle “M3-1” will be charged until the ISO quota is needed again. If this happens, the charging current for the 
Mode 3 charging vehicles is reduced accordingly. ISO charging vehicles always have higher priority. 
 

Summary of Contents for KeContact Series





























































































































































Reviews: