Keba KeContact Series System Manual Download Page 16 | Manualshive

Page: 16 / 156

background image

Hardware installation

16 / 156

4 Hardware installation

4.1 Common power line

The Wallboxes must be connected to one common power line with protective devices, otherwise the KeCon-
tact M10 is not able to perform a correct load management according to the maximum available current.

A clustering of Wallboxes is not permitted!

Be aware that each wallbox has to be secured by an individual RCD. Please see the “KeContact
P20 Installation manual” for further details about installation.

Common power line

– schematic overview

DO NOT USE multiple power lines!

«
...
14
15
16
17
18
...
»

Summary of Contents for KeContact Series





























































































































































Reviews:

No comments

Related manuals for KeContact Series

Brand: Hach Pages: 2

Brand: Hach Pages: 12

Brand: Hach Pages: 472

Brand: Hach Pages: 64

Brand: V2 ELETTRONICA Pages: 6

Brand: Hach Pages: 210

Brand: Samson Pages: 2

Brand: Laser Pages: 2

Brand: LAS Pages: 6

Brand: Lars Thrane Pages: 141

Brand: DigiPower Pages: 27

SYSMAC C500-NC222-E

Brand: Omron Pages: 164

Brand: Omniflex Pages: 2

Lux Intelligent

Brand: Advanced Pages: 62

Brand: intech 21 Pages: 15

Brand: Xsens Pages: 17

Brand: YASKAWA Pages: 12

Brand: Heat & Cool Pages: 5

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands