manualshive.com logo in svg

Keba KeContact Series, System Manual

Share
Download
Keba KeContact Series System Manual Download Page 83

Load management program 

 

83 / 156 

6.6.3  Power Profile configuration 

Overview screen that shows all existing Power Profiles. 
 

 

Configuration menu - Power Profiles 

 
 

Power Profile details 

Valid from: 

Point in time at which the validity of a power profile begins. A Power Pro-
file remains valid until its successor gets valid. 

 

Special Day: 

Special day at which the Power Profile overrides the currently active 
Power Profile. 

 

Max. Current [A]: 

Maximum current (in Ampere) that can be offered in aggregate to all Elec-
tric Vehicles connected to the Charge Point when the Power Profile is 
applicable. 

 

System generated? 

Indicates whether the Power Profile is system generated.  
If you change the Maximum current, a new “system generated” Power 
Profile will be created. 
 

DSO generated? 

Indicates whether the Power Profile is DSO (OCPP) generated. 
 

 

Summary of Contents for KeContact Series





























































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands