manualshive.com logo in svg

Keba KeContact Series, System Manual

Share
Download
Keba KeContact Series System Manual Download Page 86

Load management program 

86 / 156 

 

Typical workflow: Scheduling available energy (new Power Profile) 

 

 

►

 

Press the 

[Configuration]

 button 

 in the toolbar at the bottom of the screen. 

 

►

 

Click at the button 

[Power Profile]

 in the menu bar at the left side of the web page. The power 

profile configuration screen appears. 
 

►

 

Press the 

[New]

 button below the table of the available power profiles. The power profile editor 

screen appears. 
 

►

 

Enter the details about the power profile (valid from, special day ...). 
One after the other enter details about the power profile items. Previously entered power profile 
items can be selected from the drop down box with the label "Power Profile Item Name". 
For a power profile item, enter the power profile entries into the table "power profile entries". 
 

►

 

Press the 

[Save]

 button to save the Power profile. 

 

►

 

Return to the home screen by clicking on the 

[HOME]

 button 

. 

 
 

Summary of Contents for KeContact Series





























































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands