Keba KeContact Series System Manual Download

Page: 131 / 156

Load management program

131 / 156

6.9.5 Diagnostics information

Screen to create and export diagnostics information to a zip file.

Service menu

– Diagnostics Information

Buttons

Delete:

Press the [Delete] button, to delete the selected diagnostics files ar-
chives.

Download:

Press the [Download] button, to download the selected diagnostics file
archive.

New:

Press the [New] button, to generate a new diagnostics file archive.

Diagnostic files

packed in a zip file are intended to use by service technicians and developers only and can

be downloaded in the “Service menu – Diagnostics” screen.

In case of unexpected errors, please send these files to the customer support with your service
request.

Summary of Contents for KeContact Series





























































































































































Search results

Summary of Contents for KeContact Series

Reviews:

Related manuals for KeContact Series

Brands by name

Popular brands

Keba KeContact Series, System Manual

Search results

Summary of Contents for KeContact Series

Reviews:

Related manuals for KeContact Series

Brands by name

Popular brands