Keba KeContact Series System Manual Download

Page: 126 / 156

Load management program

126 / 156

6.9.2 Firmware Update

Screen to import and install firmware updates for the Wallboxes attached to the KeContact M10.

Service menu

– Firmware update

Currently installed firmware version

Installed firmware version:

The firmware version that is currently installed at the KeContact M10.

Time installed:

The date and time at which the currently installed firmware version has
been installed at the KeContact M10.

Firmware versions

Firmware version:

A firmware version for which a package is available at the KeContact
M10.
The table contains all firmware version packages that have been previ-
ously uploaded.

Date uploaded:

The date and time at which the firmware version has been uploaded to
the KeContact M10.

Summary of Contents for KeContact Series





























































































































































Search results

Summary of Contents for KeContact Series

Reviews:

Related manuals for KeContact Series

Brands by name

Popular brands

Keba KeContact Series, System Manual

Search results

Summary of Contents for KeContact Series

Reviews:

Related manuals for KeContact Series

Brands by name

Popular brands