Jungheinrich EKS 314, Operating Manual

Page: 84 / 225

G 3
0708
.USA
Hydraulic hoses: The hoses must be renewed every six years.
Maintenance and inspection safety rules: When lifting industrial trucks for repair
or inspection purposes, this must be done in a reliable, secured, and stable manner.
Removing components such as counter weights or support pairs will change the cent-
er of gravity position and may result in an instable state.
Before commencing inspection and repair:
– Lift the drive wheels until the are clear off the floor, disconnect the battery and use
chocks or other form-fit devices to prevent the industrial truck from moving;
– Block load lifting device, inner mast(s) or frames before starting work on these com-
ponents;
– Disconnect the battery before performing work on the electrical system;
– Plug the charger’s connector into the battery socket only, never into the industrial
truck’s socket.
Operation of the industrial truck for performance testing must occur in a specified and
restricted area with a safety clearance maintained.
1. Before starting the industrial truck, the operator must read the section “Starting
up the truck” in Chapter E.
2. When leaving the industrial truck unobserved (see section “Parking the truck
securely” in Chapter E):
– Never park the truck on an incline;
– Bring the industrial truck to a complete halt;
– Completely lower the load lifting device;
– Set the keyswitch to “0” and remove the safety key;
– Press the main switch or the EMERGENCY DISCONNECT switch;
Prevent fire hazards and make sure fire fighting facilities are available in the work ar-
ea. The use of open flames to check the level of liquids or to check for spilt liquids, in
particular of battery electrolytes, is not permitted. Open fuel pans or flammable
cleansers to clean components must not be used.
Ensure sufficient ventilation of the work area and keep the workshop clean and dry.
Brakes, steering, control devices, warning systems, lighting, controllers, lifting cut out
devices, protection and safety systems, lift devices, stops pf pivoted axles and frame
components must be carefully and regularly inspected and kept in a safe condition.
Special trucks or devices designed and approved for hazardous area operation shall
receive special attention to ensure that maintenance preserves the original, approved
safe operating features.
All hydraulic systems should be regularly inspected and maintained. Hydraulic cylin-
ders, valves, hoses, fittings, and other hydraulic components should be checked to
ensure that drift
or leakage has not developed to the extent that it would create a haz-
ard.
The truck manufacturer's capacity, operation, and maintenance instruction plates,
tags, and decals shall be maintained in legible condition.
G 3
0708
.USA
Hydraulic hoses: The hoses must be renewed every six years.
Maintenance and inspection safety rules: When lifting industrial trucks for repair
or inspection purposes, this must be done in a reliable, secured, and stable manner.
Removing components such as counter weights or support pairs will change the cent-
er of gravity position and may result in an instable state.
Before commencing inspection and repair:
– Lift the drive wheels until the are clear off the floor, disconnect the battery and use
chocks or other form-fit devices to prevent the industrial truck from moving;
– Block load lifting device, inner mast(s) or frames before starting work on these com-
ponents;
– Disconnect the battery before performing work on the electrical system;
– Plug the charger’s connector into the battery socket only, never into the industrial
truck’s socket.
Operation of the industrial truck for performance testing must occur in a specified and
restricted area with a safety clearance maintained.
1. Before starting the industrial truck, the operator must read the section “Starting
up the truck” in Chapter E.
2. When leaving the industrial truck unobserved (see section “Parking the truck
securely” in Chapter E):
– Never park the truck on an incline;
– Bring the industrial truck to a complete halt;
– Completely lower the load lifting device;
– Set the keyswitch to “0” and remove the safety key;
– Press the main switch or the EMERGENCY DISCONNECT switch;
Prevent fire hazards and make sure fire fighting facilities are available in the work ar-
ea. The use of open flames to check the level of liquids or to check for spilt liquids, in
particular of battery electrolytes, is not permitted. Open fuel pans or flammable
cleansers to clean components must not be used.
Ensure sufficient ventilation of the work area and keep the workshop clean and dry.
Brakes, steering, control devices, warning systems, lighting, controllers, lifting cut out
devices, protection and safety systems, lift devices, stops pf pivoted axles and frame
components must be carefully and regularly inspected and kept in a safe condition.
Special trucks or devices designed and approved for hazardous area operation shall
receive special attention to ensure that maintenance preserves the original, approved
safe operating features.
All hydraulic systems should be regularly inspected and maintained. Hydraulic cylin-
ders, valves, hoses, fittings, and other hydraulic components should be checked to
ensure that drift
or leakage has not developed to the extent that it would create a haz-
ard.
The truck manufacturer's capacity, operation, and maintenance instruction plates,
tags, and decals shall be maintained in legible condition.