Jeep Liberty 2011 Page 461 Owner'S Manual Download | Manualshive

Page: 461 / 540

background image

CAUTION! (Continued)

•

This vehicle has not been designed for use with
Propylene Glycol based engine coolant (anti-
freeze). Use of Propylene Glycol based engine
coolant (antifreeze) is not recommended.

Adding Engine Coolant

Your vehicle has been built with an improved engine
coolant (antifreeze) that allows extended maintenance
intervals. This engine coolant (antifreeze) can be used up
to five years or 104,000 miles (169 000 km) before
replacement. To prevent reducing this extended mainte-
nance period, it is important that you use the same
engine coolant (antifreeze) throughout the life of your
vehicle.

Please review these recommendations for using Hybrid
Organic Additive Technology (HOAT) engine coolant
(antifreeze). When adding engine coolant (antifreeze):

•

The manufacturer recommends using MOPAR

威

Antifreeze/Coolant 5 Year/100,000 Mile Formula
HOAT (Hybrid Organic Additive Technology) or
equivalent.

•

Mix a minimum solution of 50% HOAT engine coolant
and distilled water. Use higher concentrations (not to
exceed 70%) if temperatures below

⫺

34°F (

⫺

37°C) are

anticipated.

•

Use only high purity water such as distilled or deion-
ized water when mixing the water/engine coolant
(antifreeze) solution. The use of lower quality water
will reduce the amount of corrosion protection in the
engine cooling system.

7

MAINTAINING YOUR VEHICLE

459

«
...
459
460
461
462
463
...
»

Summary of Contents for Liberty 2011





























































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for Liberty 2011

Brand: Daihatsu Pages: 1718

Brand: RACLET Pages: 48

Brand: RACLET Pages: 31

Brand: Porsche Pages: 51

Brand: Whispbar Pages: 14

3-series convertible

Brand: BMW Pages: 98

Brand: FORM FIT Pages: 2

Brand: Blue Ox Pages: 7

Brand: Shad Pages: 3

Brand: TBC Pages: 12

AAB-P-RZR900-K2-001

Brand: SuperATV Pages: 3

Brand: Volvo Pages: 42

Brand: Fab Fours Pages: 21

Brand: FALCON RIDGE Pages: 4

Brand: Hummer Pages: 31

Brand: Bestop Pages: 4

Brand: TrailFX Pages: 2

PRIME DESIGN HRR3-E-PM42

Brand: Safe Fleet Pages: 12

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands