manualshive.com logo in svg

Jeep Liberty 2011, Owner'S Manual, Page: 200 / 540

Share
Download
Jeep Liberty 2011 Owner'S Manual Download Page 200

ELECTRICAL POWER OUTLET

Your vehicle is equipped with a fused 12 Volt (13 Amp)
power outlet. This power outlet is located on the instru-
ment panel, below the climate controls. It has power
available when the ignition switch is in the ON or ACC
position.

Insert the cigar lighter or accessory plug into the outlet
for use to ensure proper operation.

NOTE:

To ensure proper operation a MOPAR

威

knob

and element must be used.

CAUTION!

•

Do not exceed the maximum power of 160 Watts
(13 Amps) at 12 Volts. If the 160 Watt (13 Amp)
power rating is exceeded the fuse protecting the
system will need to be replaced.

•

Power outlets are designed for accessory plugs
only. Do not insert any other object in the power
outlets as this will damage the outlet and blow the
fuse. Improper use of the power outlet can cause
damage not covered by your warranty.

Front Power Outlet

198

UNDERSTANDING THE FEATURES OF YOUR VEHICLE

Summary of Contents for Liberty 2011





























































































































































































































































































































































































































































































































































Reviews:

No comments