Home
/
Jeep
/
Liberty 2011
/
Owner'S Manual

Jeep Liberty 2011, Owner'S Manual, Page: 141 / 540

Share

Page: 141 / 540

Jeep Liberty 2011 Owner'S Manual Download Page 141

Driver’s Power Seat — If Equipped

The power seat switch is located on the outboard side of
the seat near the floor. Use this switch to move the seat up
or down, forward or rearward or to tilt the seat.

Adjusting The Seat Forward Or Rearward

The seat can be adjusted both forward and rearward.
Push the seat switch forward or rearward, the seat will
move in the direction of the switch. Release the switch
when you have reached the desired position.

Adjusting The Seat Up Or Down

The height of the seats can be adjusted up or down. Pull
upward or push downward on the seat switch, the seat
will move in the direction of the switch. Release the
switch when you have reached the desired position.

Tilting The Seat Up Or Down

The angle of the seat cushion can be adjusted in four
directions. Pull upward or push downward on the front
or rear of the seat switch, the front or rear of the seat
cushion will move in the direction of the switch. Release
the switch when you have reached the desired position.

Power Seat Switch

3

UNDERSTANDING THE FEATURES OF YOUR VEHICLE

139

«
...
139
140
141
142
143
...
»

Summary of Contents for Liberty 2011





























































































































































































































































































































































































































































































































































Reviews:

No comments