manualshive.com logo in svg

Jeep Liberty 2011, Owner'S Manual, Page: 331 / 540

Share
Download
Jeep Liberty 2011 Owner'S Manual Download Page 331

N

Neutral - This range disengages both the front driveshaft
and rear driveshaft from the powertrain. To be used for
flat towing behind another vehicle. Refer to “Recreational
Towing” in “Starting and Operating” for further
information.

Transfer Case Position Indicator Lights

The four-wheel drive indicator lights (4WD, 4 LOW) are
located in the instrument cluster. The NEUTRAL indica-
tor light is located on the transfer case switch. If there is
no indicator light on or flashing, the transfer case posi-
tion is two-wheel drive (2WD). If the indicator light is on,
the desired position (4WD AUTO, 4WD LOW, or NEU-
TRAL) has been obtained.

If one or more shift requirements are not met:

•

An indicator light will flash.

•

The transfer case

will not

shift.

NOTE:

The “SERV 4WD Warning Light” monitors the

electric shift four-wheel drive system. If this light re-
mains on after engine start up, or it illuminates during
driving, it means that the four-wheel drive system is not
functioning properly and that service is required.

Shifting Procedures

NOTE:

If any of the requirements to select a new

transfer case position have not been met, the transfer case
will not shift, the indicator light for the previous position
will remain on, and the newly selected position indicator
light will continue to flash until all the requirements for
the selected position have been met. To retry a shift, move
the transfer case switch back to the original position,
make certain all shift requirements have been met, wait
five seconds, and try the shift again.

5

STARTING AND OPERATING

329

Summary of Contents for Liberty 2011





























































































































































































































































































































































































































































































































































Reviews:

No comments