manualshive.com logo in svg

Jeep Liberty 2011, Owner'S Manual, Page: 166 / 540

Share
Download
Jeep Liberty 2011 Owner'S Manual Download Page 166

WINDSHIELD WIPERS AND WASHERS

The windshield wiper/washer control lever is located on
the right side of the steering column. The front wipers are
operated by rotating a switch, located at the end of the
lever. For information on using the rear window wiper/
washer, refer to “Rear Window Features” in “Under-
standing the Features of Your Vehicle”.

Windshield Wiper Operation

Rotate the end of the lever upward to the second detent past
the intermittent settings for low-speed wiper operation.

Rotate the end of the lever upward to the third detent past
the intermittent settings for high-speed wiper operation.

Wiper/Washer Lever

Front Wiper Control

164

UNDERSTANDING THE FEATURES OF YOUR VEHICLE

Summary of Contents for Liberty 2011





























































































































































































































































































































































































































































































































































Reviews:

No comments