manualshive.com logo in svg

Jeep Liberty 2011, Owner'S Manual, Page: 366 / 540

Share
Download
Jeep Liberty 2011 Owner'S Manual Download Page 366

WARNING!

Overloading of your tires is dangerous. Overloading
can cause tire failure, affect vehicle handling, and
increase your stopping distance. Use tires of the
recommended load capacity for your vehicle. Never
overload them.

TIRES — GENERAL INFORMATION

Tire Pressure

Proper tire inflation pressure is essential to the safe and
satisfactory operation of your vehicle. Three primary
areas are affected by improper tire pressure:

Safety

WARNING!

•

Improperly inflated tires are dangerous and can
cause collisions.

•

Under-inflation increases tire flexing and can re-
sult in over-heating and tire failure.

•

Over-inflation reduces a tire’s ability to cushion
shock. Objects on the road and chuckholes can
cause damage that result in tire failure.

•

Unequal tire pressures can cause steering prob-
lems. You could lose control of your vehicle.

•

Over-inflated or under-inflated tires can affect
vehicle handling and can fail suddenly, resulting
in loss of vehicle control.

(Continued)

364

STARTING AND OPERATING

Summary of Contents for Liberty 2011





























































































































































































































































































































































































































































































































































Reviews:

No comments